36V Smart Lithium Battery Vertical Torque Wrench

1. Scope of Application

1. Bolt disassembly in the field of rail transit.

2. Maintenance of construction machinery and special vehicles.

3. Bolt fastening for engineering construction.

2.Main Technical Parameters

1. Rated voltage: DC 36V

2. No load speed: 0-1250 rpm

3. Frequency: 0-2500 / min

4. Weight: 12.2kg

5. Maximum torque: 2000N · M

6. Overall dimension: 850x330x135mm

7. Charging voltage: AC 220V

8. Battery voltage: DC 36V

3.Safety Precautions

This manual contains important safety and operating instructions for batteries and chargers. Before using the charger, please read all instructions and warnings on the charger, battery pack and the tool.19 • if the battery pack box is cracked or damaged, do not insert it into the charger. Because it can cause an electric shock. • do not allow liquid to enter the charger because it may cause an electric shock. After use, in order to facilitate the cooling of the battery pack, do not place the charger or battery pack in a hot environment without insulation, such as a metal shed or trailer. • the charger can only charge rechargeable batteries. Using it for other purposes may cause accidents such as fire. Do not place anything on the top of the charger or on a soft surface that may cause excessive internal heat. Do not place the charger near any heat source. In order to reduce the potential risk of damage to the power plug and power cord, when disconnecting the charger from the power supply, do not pull the power cord, but pull out the power plug. Make sure the power cord is in place so that it will not be stepped on, loosened or otherwise damaged or stressed. Extension cords shall not be used unless absolutely necessary. Improper use of extension cords may cause fire and electric shock hazards. Do not operate the charger if the charger is struck too hard, dropped or damaged for other reasons. • do not disassemble the charger. When maintenance or repair is20 required, please take it to the service agency. Improper reassembly may cause electric shock or fire hazard • in order to prevent the risk of electric shock, unplug the charger from the power socket before wiping the charger. Removing the battery pack from the charger is not sufficient to reduce the risk of electric shock. • do not store the tool, charger and battery pack in places where the temperature may reach or exceed 40 ° C, and do not use the tool in such places, as this will lead to battery deterioration. • the charger can only be used on standard household power supply (100 ~ 240V AC). Do not try to use the charger on any other power supply. Additional information on batteries and chargers The battery pack was not fully charged when removed from the box. First, please read the instructions, and then follow the charger instructions and steps. If the battery pack is charged at an air temperature between 18 ℃ and 25 ℃, the service life of the battery pack is long and the performance is the best. When the battery pack is charged at the temperature of - 20 ℃ or above - 45 ℃, the battery pack will be automatically disconnected from charging21 Even if the battery pack is seriously damaged or completely damaged, the battery pack shall not be incinerated. Because the battery will explode in a fire. Never try to open the battery pack for any reason. If the plastic case of the battery pack breaks, stop using it immediately and do not charge it. The service life of the battery depends on the type of work. This battery has the longest trouble free service life. However, like all batteries, it will eventually wear out. In order to obtain the longest possible battery life, we give the following suggestions: Store the battery in a cool area and charge it in that area. Temperatures above or below normal room temperature will shorten the service life of the battery. • never store the battery after discharge. Recharge the battery immediately after discharge. • all batteries lose power gradually. The higher the temperature, the faster the battery loses power. If the tool is stored for a long time without use, the battery must be charged every one or two months. This can prolong the service life of the battery. Charging steps:22 Connect the plug to the charger first, and then plug the charger into a suitable power socket before inserting the battery pack Insert the battery pack into the charger to ensure that the battery pack is safely installed in the charger. During charging, the charging indicator will display the charging status: -The power indicator will flash successively with the increase of power until all lights are on. -After the battery is fully charged, the four charging indicators will remain on continuously. • the charging process lasts about 3 hours, and the power indicator is always on, indicating that the charging is completed. _ Unplug the charger and the indicator light goes out. If the power is observed, long press the lithium battery pack switch to observe the power.

Hot Tags: 36v smart lithium battery vertical torque wrench, China, manufacturers, suppliers, made in China, railway wrench, special track hand tool, custom track spanner, railroad pneumatic tool, repair track hand tool, precision track wrench